Do you need to reset your Kenwood ProTalk business radio back to its original factory configuration? It's really easy. In this episode of Radio 101, Anthony from Buy Two Way Radios will show you how to do it in two simple steps. This method works for Kenwood ProTalk 200, 300 and 400 Series business two way radios, including the TK-2200V2P, TK-2200V8P, TK-2300V4P, TK-2300V16P, TK-2400V4P, TK-2400V16P, TK-3200U2P, TK-3200LU15P, TK-3300U4P, TK-3300U16P, TK-3400U4P, and TK-3400U16P.
- Home
- Business Radios
- Consumer Radios
- Accessories
- Antennas
- Antenna Analyzers
- Audio Accessories
- Batteries
- Belt Clips
- Bundles and Kits
- Cases and Holsters
- Chargers
- Coaxial Cable
- DC Power Accessories
- DC Power Supplies
- Dummy Loads
- Duplexers
- Faraday Bags
- Miscellaneous Accessories
- Mounts
- Power SWR Meters
- Programming Cables and Software
- Replacement Parts
- Solar
- Test Equipment
- By Radio Type
- By Radio Brand
- Services
- Other Products
- Buyer's Guide
- Resources
I recently received a Kenwood transceiver in the mail - no shipping information - other than the box. There was not power supply, microphone or manual of any kind. I'd love to get it working (if the cost is minimal).. It appears to be a service business radio of some type. If you have any ideas let me know.
Dennis W Pollard
W0PO
I have a pair of Kenwood tk-3360-k radios and i tried your resetting method, nothing.
Bryce, the TK-3360 is not included on our list of Kenwood models intended for using this reset method.
I have two TK-3400U16P radios, both charge up and turn on. But they do not talk to each other. I tried resetting both and found the procedures to do so, by turning on the unit while holding down the two side buttons and talk button. When I do this the units LED turns blue and beeps then both turn off. The unit doesn't speak or the LED doesn't turn orange. I've tried letting go of the buttons at 1 sec, 2 sec and longer after it beeps and no difference other than it beeps with a different tone if I hold then release after 2 seconds.
Any Ideas ?
How can i reset my KT3310 KENWOOD RADIO PLEASE
Hi, what is the meaning of the following message on Protalk XLS display?
Un PG - doesn't go away without factory reset.
If the procedure is not listed in the manual, it may not have a user accessible reset option.
I have a set of kenwood tk-3160 if there an easy way to reset them? thank you.
20 Kenwood TK3160M where given me by my local recycling company
The radios were locked, is there a master reset for the TK-3160M
We are going to reprogram the radio to ham band if pass FCC after reprogramming
Steven Rogge
K6XZ
Hi dears, i have kenwood TH-2140. can you tell me how reset it in factory configuration.
tks
can i reset or recover the password of my kenwood tk-3000 ?
i bought me a used kenwood tk-3212 radio, but i want to reset it to its original factory configuration. i dont know if thats possible?and if yes.how can i do it?? i need it for my job since i lost the one they gave me and if i dont replace it they are going to charge.i would aprecciate any tip,thanks..
How do you reset a kenwood tk-2140 radio
I have 4 tk-3400u4p radios. Three work fine. The fourth we can listen but when the Ptt button is depressed the led turns red. Kenwood told me that someone needs to hook it up to a computer and make it back into a pro talk radio. Is this true